Frame and Body Parts

Go Kart Frame Parts | Go Cart Body Parts 

We carry a full line of off road go kart frame and body parts for Hammerhead, Yerf Dog, TrailMaster, Carter Brothers, BMS, Dongfang and Manco go karts.

Items: 112 of 35, per page
  • This is a fuel tank for most 150cc gokarts (13-0629-01 OR 4.000.011), including Hammerhead, Trailmaster, and Twister karts. 
    This new-style gas tank uses gas cap 18-0232-01. 
    This may also have a hole for a roll-over valve.

    • $79.99

    Score: 5.00 (votes: 1)
  • Universal Gas Cap (6.000.145) (6.000.053)

    • $12.99

    Score: 5.00 (votes: 1)
  • Pedal - Brake Pedal for most 150cc and 250cc Go Carts Karts.

    • $35.99

    Score: 5.00 (votes: 1)
  • 4.000.016, THROTTLE PEDAL COMP.

    • $35.99

    Score: 5.00 (votes: 1)
  • Tie Rod End for 150cc & 250cc Hammerhead Go Carts Karts 6.000.062

    • $20.00

    Score: 5.00 (votes: 1)
  • Dust cover for Hub for nearly all Hammerhead makes and models.  Works on both front and rear hubs.  

    • $6.99

    Score: 5.00 (votes: 1)
  • Hammerhead Seat Belt Assembly 5-Point - 6.000.354 replaces 6000354150G000, 50116, 6000356150G000

    • $99.99

    Score: 5.00 (votes: 1)
    Only 10 left in stock
  • Hammerhead GTS 150, 150 XRX, 300 XRX Go Cart Kart Speedometer 

    • $79.99

    Score: 5.00 (votes: 1)
  • Hammerhead Dash Board / Switch Panel Cover for GTS 150 / Platinum GTS - 7.110.038

    The switch panel cover on a Hammerhead GTS 150, SS250, or GTS250 go-kart is likely a protective cover that houses the various switches and controls for the vehicle. This cover helps shield the switches from dirt, debris, and damage while also providing a neat and organized appearance.

    If you're looking to replace or install a switch panel cover on your Hammerhead go-kart, here are some general steps you might follow:

    1. Purchase the Correct Cover: Make sure you have the correct switch panel cover for your specific Hammerhead model (GTS 150, SS250, or GTS250). These models might have slightly different designs, so it's important to choose the right cover.

    2. Gather Tools and Parts: You'll need the new switch panel cover, any necessary screws or fasteners, and the tools required for installation. These might include screwdrivers, wrenches, or other basic hand tools.

    3. Safety First: Ensure the go-kart is parked on a level surface and the engine is off. If the go-kart has a battery, disconnect it to avoid any accidental electrical issues.

    4. Remove the Old Cover (If Applicable): If you're replacing an existing switch panel cover, carefully remove it by unscrewing any fasteners that hold it in place. Keep track of the screws and their positions for reassembly.

    5. Position the New Cover: Align the new switch panel cover with the appropriate slots or mounting points on the go-kart's frame. Make sure it fits properly and is oriented correctly.

    6. Secure the Cover: Using the provided screws or fasteners, attach the new switch panel cover to the go-kart's frame. Tighten the screws securely but avoid over-tightening to prevent damage.

    7. Test the Switches: After the cover is securely in place, test all the switches and controls located within the switch panel. This ensures that everything is connected properly and functioning as intended.

    8. Reconnect Battery (If Applicable): If you disconnected the go-kart's battery earlier, now is the time to reconnect it.

    9. Inspect and Finalize: Double-check all screws, fasteners, and connections. Make sure the cover is flush and secure. Verify that the switches and controls operate smoothly.

    Remember that these steps are general guidelines, and the specific process might vary based on the exact model of your Hammerhead go-kart. Always refer to the manufacturer's manual or seek guidance from a professional mechanic if you're unsure about any aspect of the process. Safety is of utmost importance when working on vehicles, so take all necessary precautions.

    • $59.99

    Score: 5.00 (votes: 1)
  • Steering Gear Assy w/ 45 Degree Angle (4.000.008-250)

    • $99.99

    Score: 5.00 (votes: 1)
  • 4.000.008-GTS, Steering Gear, narrow 45 - R-150 & GTS250

    • $99.99

    Score: 5.00 (votes: 1)
  • Steering knuckle that is used on many Chinese go-karts, both 150cc and 250cc. 

    This knuckle measures roughly around 11 3/4" - 12"

    • $59.99

    Score: 5.00 (votes: 1)
Items: 112 of 35, per page
Bestsellers